The continuity equation for incompressible flow states that:

The correct answer is A: A₁V₁ = A₂V₂. The continuity equation for incompressible flow is based on mass conservation: ρA₁V₁ = ρA₂V₂, which simplifies to A₁V₁ = A₂V₂ when density is constant.

A fluid element has shear stress τ = 0.5 Pa and velocity gradient du/dy = 10 s⁻¹. The dynamic viscosity of the fluid is:

The correct answer is A: 0.05 N·s/m². From Newton's law of viscosity, τ = μ(du/dy), so μ = τ/(du/dy) = 0.5/10 = 0.05 N·s/m²

In journal bearing design, if the bearing length is doubled while keeping other parameters constant, how does the load capacity change?

The correct answer is A: Doubles. Load capacity in journal bearings is directly proportional to bearing length. Doubling the length doubles the total load-carrying area, thereby doubling the load capacity.

Two bodies at different temperatures are brought into contact in an isolated system. The total entropy of the system will:

The correct answer is C: Increase. For an irreversible process in an isolated system, total entropy increases (ΔS_total > 0). Heat transfer between bodies at different temperatures is irreversible.

Which of the following is the primary function of a flexible coupling in machine design?

The correct answer is B: To accommodate slight misalignment between shafts and reduce vibration. Flexible couplings are designed to accommodate angular, parallel, and axial misalignments while reducing shock loads and vibrations transmitted between shafts.

Home

Home › Subjects › Mechanical Engineering › Machine Design

Mechanical Engineering
Machine Design

Thermodynamics, hydraulics, machine design

23 Q 3 Topics Take Mock Test

Difficulty: All Easy Medium Hard 1–10 of 23

Topics in Mechanical Engineering

All Thermodynamics 100 Fluid Mechanics 79 Machine Design 80

Q.1 Easy Machine Design

Which type of gear arrangement is suitable for power transmission between skew axes?

A Spur gears

B Helical gears on parallel shafts

C Worm and worm gear

D Bevel gears

Correct Answer: C. Worm and worm gear

EXPLANATION

Worm and worm gear drives are specifically designed for non-parallel, non-intersecting skew axes with large speed reduction.

Test

Q.2 Easy Machine Design

In gear nomenclature, what does the module represent?

A Pitch diameter divided by number of teeth

B Ratio of pitch circle diameter to number of teeth

C Center distance between gears

D Diametral pitch in metric system

Correct Answer: B. Ratio of pitch circle diameter to number of teeth

EXPLANATION

Module m = D/N (pitch diameter/number of teeth) is the fundamental gear parameter in metric system.

Test

Q.3 Easy Machine Design

Which of the following is NOT a function of a coupling in power transmission systems?

A Transmit torque

B Accommodate axial misalignment

C Change speed ratios between shafts

D Reduce vibration and shock loads

Correct Answer: C. Change speed ratios between shafts

EXPLANATION

Couplings transmit power but do not change speed ratios; gear boxes and belt drives perform that function.

Test

Q.4 Easy Machine Design

What is the primary advantage of using roller bearings over ball bearings in heavy industrial applications?

A Lower cost

B Higher load carrying capacity for radial loads

C Better high-speed performance

D Simpler installation

Correct Answer: B. Higher load carrying capacity for radial loads

EXPLANATION

Roller bearings have larger contact area and can sustain higher radial loads compared to ball bearings.

Test

Q.5 Easy Machine Design

A journal bearing is subjected to a radial load of 10 kN with shaft speed of 600 rpm. If bearing length is 80 mm and shaft diameter is 50 mm, find the bearing pressure (Hertzian pressure approximation).

A 2.5 MPa

B 3.75 MPa

C 5.0 MPa

D 6.25 MPa

Correct Answer: A. 2.5 MPa

EXPLANATION

Bearing pressure P = Load/(d × l) = 10000/(50 × 80) = 2.5 MPa.

Test

Q.6 Easy Machine Design

Which of the following materials is preferred for manufacturing flexible couplings?

A Cast iron

B Rubber or polyurethane elastomers

C High carbon steel

D Aluminum alloys

Correct Answer: B. Rubber or polyurethane elastomers

EXPLANATION

Elastomeric materials in flexible couplings provide damping, shock absorption, and vibration isolation capabilities.

Test

Q.7 Easy Machine Design

In a spur gear design, what is the primary function of backlash?

A To increase load carrying capacity

B To allow for thermal expansion and manufacturing tolerances

C To reduce noise generation

D To improve gear meshing efficiency

Correct Answer: B. To allow for thermal expansion and manufacturing tolerances

EXPLANATION

Backlash is intentionally provided to accommodate thermal expansion, manufacturing errors, and to prevent gear jamming.

Test

Q.8 Easy Machine Design

Which type of bearing is preferred for applications requiring self-alignment capability?

A Deep groove ball bearing

B Spherical roller bearing

C Cylindrical roller bearing

D Angular contact bearing

Correct Answer: B. Spherical roller bearing

EXPLANATION

Spherical roller bearings have a spherical outer raceway that allows self-alignment up to 2-3 degrees, making them ideal for misaligned shaft applications.

Test

Q.9 Easy Machine Design

A hollow shaft has an outer diameter of 60 mm and inner diameter of 40 mm. What is the polar moment of inertia of the shaft?

A 101,788 mm⁴

B 152,681 mm⁴

C 203,575 mm⁴

D 305,363 mm⁴

Correct Answer: C. 203,575 mm⁴

EXPLANATION

J = (π/32) × (D₀⁴ - D_i⁴) = (π/32) × (60⁴ - 40⁴) = 203,575 mm⁴

Test

Q.10 Easy Machine Design

In a worm gear drive with a single-start worm, module 2 mm, and 40 teeth on the gear, what is the worm pitch?

A 2 mm

B 4 mm

C 6 mm

D 8 mm

Correct Answer: A. 2 mm

EXPLANATION

For a worm gear, pitch = module × number of starts = 2 × 1 = 2 mm (for a single-start worm)

Test

1 2 3

All Subjects & Topics

Govt. Exams

Entrance Exams

Teacher Exams

Subjects

Quick Links

Mechanical Engineering Machine Design

Mechanical Engineering
Machine Design